Power Source
- AC: 230 V
- DC: 24 V/7.5 A
- Applicable cable diameter: AWG22 – AWG14
Power Consumption on AC Mains
- With no signal present: 37 W
- Under normal operating conditions according to
- EN60065: 1998 sec. 4.2: 107 W
- With rated output signal: 201 W
Current Consumption on 24 V DC Power Input
- With no signal present: 0.7 A
- Under normal operating conditions according to
- EN60065: 1998 sec. 4.2: 2.1 A
- With rated output signal: 5.2 A
Rated Output : 120 W
Output Voltage /Impedance : 100 V/83 Ω ( selectable by the internal wiring change )
Frequency Response : 50 Hz – 16 kHz
Distortion : 1 % or less
Signal-to-Noise Ratio : 60 dB or more
Tone Control : Bass: 100 Hz ±10 dB (Inputs 1 – 3 and BGM individually adjustable.)
Remote Microphone /Expansion Amplifier Connection
- 2 RJ45 female connectors for connecting the RM-200M Remote
- Microphone and the VM-2120 or VM-2240 unit used as an
- expansion amplifier.
- Maximum distance: 800 m (874.89 yd) in total
- Link cable: Category 5 Shielded
- Number of connectable RM-200M’s: Up to 4
- Twisted-Pair straight cable (TIA/EIA-568A standard)
Input
- Inputs 1 – 3: -60 dB(*3) (MIC)/-10 dB(*3) (LINE) (changeable)
- 600 Ω
- combined XLR connector (female)/phone jack (Only Input 1 is additionally equipped with DIN connector(*5).)
- Telephone paging input: Push-in terminal block(*6)
- Voice sound: -10 dB(*3)
- balanced input with shield terminal(*4)
- Control: No-voltage make contact input
- open voltage: 3.3 V DC
- short-circuit current: under 1 mA
- BGM 1 – 2: -20 dB(*3)
- Power amplifier input: 0 dB(*3)
- External speaker line input: 100 V line (This input is selected when the “Unit’s broadcast cutoff” control is activated.)
Output
- Speaker output: Plug-in screw connector(*7)
- 5-zone selector with attenuator (all zones simultaneously selectable)
- Direct speaker line output: Direct output from the power amplifier
- output transformer (attenuator bypassed)
- Plug-in screw connector(*7)
- Line output: 0 dB(*3)
- Recording output: 0 dB(*3)
- Preamplifier output: 0 dB(*3)
Control Input
- For controlling Inputs 1 – 3
- No-voltage make contact input
- short-circuit current: 1 mA or less
Control Input and Output
- D-sub connector (25-pin
- Input: No-voltage make contact input
- short-circuit current: 1 mA or less
- Output: Open collector output
- control current: 10 mA or less
- (1) External control input
- Activation of messages(*8)
- Activation of power
- Activation and stop of Emergency Broadcast
- Unit’s broadcast cutoff (when activated by an external emergency equipment)
- (2) Status output
- Irregularity of communications with the Remote Microphone and
- an expansion amplifier
- AC power condition
- DC power condition
- Irregularity of the sound source of the Voice Announcement Board
- Failure (FAULT) indication on
- Power switch on
External Attenuator Control Output
- Plug-in screw connector(*7)
- transfer type
- contact current: 7 A (DC) or less
Surveillance Input and Output(*9)
- D-sub connector (25-pin
- Input: No-voltage make contact input
- Output: Open collector output
Power Supply
- 24 V DC/0.1 A
- Unit RU-2001/-2002
Chime Tone
- Built-in chime: 2-tone chime/2-tone chime (fast repeat)/4-tone
- chime (Up)/Single-tone chime/4-tone chime (Up &Down)/Gong/off
- Voice Announcement Board sound source: Pre-recorded chime(*8)
Function
- Two units stacking (VM-2120 or VM-2240)
- Emergency broadcast (sequential control)
- Broadcast priority control
- Surveillance (failure detection) function(*9)
- Power supply to only one Remote Microphone (RM-200M)
- Line resistance: 40 Ω (one way) or less
Operating Temperature : 0 ℃ to +40 ℃ (32 %%dF to 104 %%dF)
Finish
- Panel: ABS resin
- Case: Steel plate
Dimensions 419 (W) × 143.3 (H) × 355.7 (D) mm (16.5 × 5.64″ × 14)
Weight : 12.5 kg (27.56 lb)
Accessory
- Power cable (2 m (6.56 ft)) ……1
- Miniature type time-lag fuse T2.5 A ……1
Option
- Rack mounting bracket: MB-36
- Input transformer: IT-450
- Voice announcement board: EV-200M
- Surveillance board: SV-200MA
